Skip to main content

Nutella and Almond Bread Maker Rolls Recipe

2016 is set to see a huge strain on our finances as I have just started maternity leave!  In an effort to save money I am operating a zero waste policy in the kitchen.  After rummaging in cupboards the other day I realised I had not only an almost full jar of Nutella that was just sitting there, but also a small amount of powdered almonds left over from the Christmas baking.  Something had to be created from these two wonderful 'leftovers'.

I am a huge fan of cinnamon rolls and a bread maker version had been on my pinterest wishlist for ages!  I'm also quite in love with an amazing chocolate brioche that Aldi sells and was wondering if I could come up with something in the same family to squash my craving.  The lightbulb moment came when I decided to combine two recipes; the breadmaker cinnamon roll recipe and one I found for Nutella and almond rolls!

The process for this is super easy and only involves about 20 minutes of actual work, the bread maker does the rest!  If you don't have a bread maker you need to get one in your life!  Read about how much money you could save with one here.

Ingredients

Makes 12

For the Dough

250ml (8 fl oz) warm milk (45 C)
2 eggs, room temperature lightly beaten
75g (3 oz) butter, melted
600g (1 1/3 lb) bread flour
1 teaspoon salt
100g (4 oz) caster sugar
2 1/2 teaspoons quick yeast
2 teaspoons almond extract

 

For the Filling 

1 jar of Nutella
50g ground almonds

 

For the Icing

90g icing sugar
4 teaspoons whole milk
1 teaspoon almond extract
1 teaspoon vanilla extract 

Method 

 

Place the dough ingredients in the bread maker in the order specified in your manual (mine is always wet ingredients first, followed by dry and then yeast, sugar and salt on top). Don't worry too much about getting your milk to the perfect temperature.  I measure mine into a microwavable mug/jug and place it on high for 30 seconds, stir and repeat until it is warm but not hot.  Select the dough cycle and press start. 
After the bread maker has finished, the dough should be doubled in size.  If it isn't place on a floured surface and cover until doubled in size (about 10 minutes).

 
 
Roll the dough out on a well floured surface to measure 40cms x 50cms.  It will be very springy and pliable, so do not force the dough with the rolling pin, just roll gently.  Make sure that you measure the dough and that it is in a rough rectangular shape.
 
Using a large spoon and either a knife or spatula carefully cover the dough in the jar of Nutella.  Once you have an even layer, sprinkle on the ground almonds.


Starting with the longer end carefully roll the dough into a spiral shape.  Make sure that it is tight enough that the Nutella was stick the dough together and it won't loose it's shape once cut.  Then divide the long sausage into 12 pieces and arrange cut side up on a well oiled tin (or 2 tins if required).  The rolls should be touching.



Cover with a piece of clingfilm and place in a warm setting for 30 minutes, they will double in size.  Whilst you are waiting for this step pre-heat the oven to 200c / fan 180c / Gas mark 6.
 
Once the buns have risen remove the clingfilm and bake in the oven for 15 - 20 minutes.  Keep an eye on them after 12 minutes as they will quickly catch, they should be a light golden brown colour.
 
While the buns are cooking mix all the icing ingredients together in a bowl.  You may need to adjust the icing sugar and milk quantities to get a nice runny paste.  Once the buns have been cooked, remove from the oven and drizzle over the icing whilst still warm.


After 10 minutes, carefully transfer the buns to a wire rack to prevent soggy bottoms!
 
These are best eaten warm, but can be re-heated in a cold oven (not pre-heated) at 160c / fan 150c for 5 minutes.  These also freeze well to ensure you always have a batch on the go!  Just defrost by placing on a wire rack for a few hours and then re-heating as usual

Comments

Popular posts from this blog

Colour B4 Extra Strength Review - Part Two Using the Dye Remover and helping to prevent re-oxidation

If you haven't already read it, you should really check out Part One of this as it details preparation, it can be found here Well it is done and I am rather impressed with the results, even if I do say so myself!  There were a few things that I did differently this time and I will go through the entire process and then share the finished result. You will need; Sectioning Clips Comb Colour B4 Extra Strength Cling Film Two beanie style hats Hair Dryer Shower Bucket Loads of Patience Step One Start by sectioning your hair and clipping the upper portion to the top of your head.  If like me you have long hair, it is best to start with the underneath layers.  I found the easiest way to apply the remover was to take a small section of hair (no more than an inch wide) and squirt a small amount into my gloved hands and start with the ends carefully rub it in.  I usually applied 3 squirts to each section; end, mid length and root.  Time should be taken to ensure each squ

Superdrug Colour Rewind - Hair Dye Remover Review - Part One

I started dying my hair at the grand old age of 15 - fast forward to 12 years later and my hair has become a dried out mop of horror.  I started with black - I loved Marilyn Manson and Slipknot and needed the world to view my hair as an extension of my sheer awesomeness!  This phase lasted until I was about 19; almost 4 years of the darkest of darks layered over my hair. I alternated between black, black-blue, black-purple and even tried dip dyed black and red.  At 19 I wanted a change and decide to bleach it so I could dye it red - after an initial day of ginger (luckily I was favouring the sporty baseball cap in this period) I switched to a dark red.  Next came a few years of alternating between different shades of red and then various browns. When we started trying for a baby in 2010 I was worried that the constant dying of my hair whilst pregnant could cause development issues - I went to a professional hair dresser and had blonde highlights put through my then dark brown

Replacement Blades for the Silhouette Cameo - UK users

From the moment I purchased my Silhouette Cameo I was in love.  The only way I could justify the cost was to start up a business , the only problem with this was the cost of the blades.  I was getting through a blade every few weeks, at just under £16.00 (including postage) for a single blade it was getting very expensive.  I knew that once business picked up I was going to either have to increase prices (never a good idea for new businesses) or take a big knock in profits.  The only solution I could see was be to try and find a cheaper solution to the blades. I was first made aware of using disposable blades by Ligaya's Creativity Zone .  She had had success with an aluminium (CB09) Blade Holder.  This blog was invaluable for advice on the different angled blades available and suppliers of the CB09 Blade Holder. The only drawbacks were the seller was based in Asia (have been stung for import taxes before, and it is a hefty amount) and there were reports that the holder act